auto sensor signal simulation tool MST-9000 operation question

           auto sensor signal simulation tool MST-9000 operation question

Q: I've bought a MST-9000 and also have been trying for doing things and display screen has locked up to and including solid blue (no text). Initial use was fine, the wakeup with energy onto a splash screen, recption menus labored and buttons responded. Energy on/off a couple of occasions with no problem. The SW was loaded to computer (XP OS per instructions) and also the SW loaded fine. Motorists for that MST-9000 USB connection put together through connection, manual find and all sorts of was OK.  A preliminary waveform was loaded towards the ECU software, saved towards the disk. After connection of USB from MST-9000  to the pc as mentioned over the MST-9000 is locked as proven in pictures below. Just the on, off and browse buttons work now. The on is on, off is off, out and browse beep at me, but read activates CH1-5. Even the 5V, 12V, and 24V buttons activate lights, gages work too for Volts, etc.

Can there be some totally reset or go back to default condition about this MST-9000. I've browse the manuals using the Compact disc(PDF's) but don't see a method to restart in initial condition. Or perhaps a SW establishing the eu software that enables the totally reset, etc.

 

                       

I attempted to energy in the MST-9000 and it is doing exactly the same problem for that display today. Please reply having a status of the recommeneded fix or resolution. If you want every other info on button press/hold or perhaps a sequence of buttons,etc. to unlock or obtain a status of the instrument tell me.

A: Book the energy   - whether connected right?

Q: I attempted this on four plugs inside my bench (computer, monitor, Voltmeter HP3478A, and also the MST-9000). All work fine, however the MST-9000 is same problem of solid lighted display. No splash screen or transition on startup visible (I looked). Attempted on same plug I initially tried on the extender for first energy on/off?¡¥s. Same problem exists now.

With this particular MST-9000 blocked on and in I recieve a tone(whine) of greater frequency that's just like a driver or display upcoverter to function the display(generally once had flicker free thought of the shows and backlighting proven about this LCD). Whine is just present using the LCD light, not the .3 sec transition from the lights off on relaxation of MST-9000.

Yes I'm an engineer and then try to observe significantly what went down (accustomed to this from work). Please reply having a next thing or how you can resolve this problem. Actually want to do this MST-9000 out being an engine simulator. Thanks.

A: Will the light flashing once you connect energy?

Q: No lights on or anything happens(lights, seem or anything I'm able to identify), before the on button is pressed. A solid light backlit around the Liquid crystal display, no transition from the light, display or change unless of course its so quick I am unable to identify it. Attempted at angles for twist of those shows with no change or "hidden" letters I'm able to identify off position(left, Right, up, lower, etc.)

A: Engineer request you alter a very oscillator near the Primary board CPU. Are you able to do that?

Q: I've opened up in the situation and viewed the board and parts having a specialist in the office.  All of the functions of energy supplies, results to board for energy, procedures from the rotary knobs (containers, current partitioning, etc.) are correct from what we should saw and measured. The display was stuck within the lighted position and that i had found the processor and very.  Attempted to press,  touch for warmth with no change around the operation. (Picture photo.digital above from the uP and very) Following a couple of tries the specialist used electronics cooling freeze and cooled the processor and very.  This had the system recover purpose of display to menu along with a beep of speaker. All was OK and good. Labored by using it for any couple of minutes to ascertain if the warmth of operation would make the failure again. Didn't fail rapidly so he used a warm air gun(controlled temp on really low setting) and attempted to warm up a little. A couple of batches as much as the roughly 70-90 deg c by feel of hands also it unsuccessful in same manner again. Then cooled the very lower and to operation. Therefore we believe it's the very while you had indicated. The Compact disc you provided has numerous PDF's and that i have looked this but don?¡¥t look for a very oscillator spec sheet. The code around the very states 11.0592, I'm able to find these easily in NA market using the leaded type used. A supplier of Newark Electronics has lots of available below to buy

Are you able to supply the specific frequency tolerance, load capacitance, frequency stability and dimension for spacing about this part(4. or 4.06 mm). Or are you able to ship a few of the deposits used and can change this here. We are able to likely change this because its wire lead part.

 

                        

 

A: I've spoken with engineer, he stated as lengthy because it is 11.0592 very then it's all ok. Same size because the one the thing is, and that he stated no need individuals data you requested, just common the first is ok, but require it is 11.0592 frequency.

Q: I've the deposits on order with Newark Electronics and can receive them middle of week.  Then attempt to swap the very and perform a burn in(operate for hrs of approximately 10-12) and find out this works adequately.